Burn your own logo, letters or text into wood with a custom branding stamp for wood:
Personalise your products with our high-quality branding irons.
A wood branding stamp allows you to easily apply a logo, letters or a name to wooden products. It is commonly used on:
Want to brand larger quantities of wooden products? One branding iron allows you to mark hundreds of products with the same logo quickly and consistently.
You do this with a heat source such as a branding iron, pyrography pen or wood burner. Want to burn the same logo into wood repeatedly? An electric branding iron for wood is the best choice. It allows you to place the same brand mark in the same position each time, without manually tracing or engraving it.
With our wood branding stamp, you can burn a logo, text or letters into wood in just 3 seconds:
Tip: A voltage regulator keeps the temperature consistent. This is useful when branding several products in succession. Clean the stamp with our brush after use.
Want to create one unique design by hand? A pyrography pen or wood burner is a good choice.
Almost every type of wood is suitable for burning a logo. The most important thing is that the wood is dry, clean and as flat as possible, so the entire branding stamp makes proper contact with the surface. The type of wood mainly determines how dark and sharp the brand mark will be.
Not sure whether your type of wood is suitable? Send us a message and we will be happy to advise you.
Choose the size based on the level of detail in your logo and where you want to burn the logo into the wood. A standard bank card measures approximately 86 × 54 mm. This makes it easy to see whether your logo will appear subtle, clearly visible or particularly large on the wood.
We make round branding stamps from 25 to 80 mm, square branding stamps from 12 × 12 to 120 × 120 mm and rectangular branding stamps from 12 × 35 to 35 × 140 mm. Need another size? Contact us about a custom branding iron.
Whether your logo can be branded clearly mainly depends on how readable the design is. A clean logo with clear shapes usually looks good in wood, while very fine lines or small letters can disappear more easily in the brand mark.
Pay particular attention to the following:
Before production, we check whether your logo is suitable for wood branding. Not sure about your design or the required size? Send us a message and we will review it with you.
At JH Machining, you can order your own branding stamp in a few simple steps and use it to burn a unique logo into wood:
Select the required size and upload your logo on the product page.
We convert your logo into a suitable file and check whether all details can be branded clearly.
Once approved, we produce your custom branding iron and test the result.
You can then start burning your logo into wood straight away.
Tip: Test the branding iron on scrap material first. This allows you to determine the right temperature and branding time for your type of wood.
For the best branding irons, look no further than JH Machining:
Order your branding iron today and present your brand in a unique way.
100% satisfied or your money back. Guaranteed.
Not completely satisfied? No problem. You can return your custom branding iron free of charge within 30 days — no questions asked.
We are one of the only suppliers offering a 100% satisfaction guarantee on custom-made branding irons, so you can order with complete confidence.
Before shipping your branding iron, we carefully test it on wood and leather. This ensures your design produces a sharp, clean and high-quality imprint.
Because of this thorough quality check, we’re confident in our product. Out of thousands of branding irons produced, only a very small number have ever been returned.
The electric heating element comes with a 2-year warranty, so you can rely on long-lasting performance.
JH Machining offers a 2-year warranty on the following products:
What does the warranty include?
If your heating element, branding iron or wax seal stamp breaks during normal use, simply return it to us. We will repair or replace the product free of charge, quickly and hassle-free.
Why our warranty is unique
JH Machining is one of the only suppliers in Europe that offers a warranty on custom-made branding irons and wax seal stamps with your own logo.
Yes, pickup is possible by appointment.
How does it work?
Because of our production schedule, pickups are available by appointment only.
Please contact us in advance to schedule a convenient time.
Pickup location
Rouaanstraat 21-F
Groningen, The Netherlands
Yes, you will automatically receive an invoice including VAT with your order.
Ordering as a business?
If you are ordering as a business within the EU, you can enter your VAT number at checkout.
In that case, the reverse-charge mechanism may apply.
You can pay with us in the following ways:
iDeal
Credit card
Bancontact
PayPal
Klarna
Direct bank transfer
Yes, we deliver to all countries in Europe and the United Kingdom.
What about shipping costs?
Shipping is completely free on all orders within these regions.
Yes, absolutely. You can choose our Express Delivery option during checkout.
How does Express Delivery work?
With Express Delivery, your order will be produced and shipped within 2 business days.
The additional cost for Express Delivery is €9.95.
Yes, absolutely. As soon as your order is handed over to the carrier, you will automatically receive a Track & Trace code.
What does this mean for you?
With your Track & Trace link, you can easily follow your shipment in real time and see exactly when your package will arrive.
The heating time depends on the size of the branding iron and the material you’re working with.
In most cases, it takes between 5 and 30 minutes for the branding iron to reach the right temperature.
What affects the heating time?
Recommended temperatures
Tip for best results
Always test your branding iron on scrap material first.
This helps you find the perfect temperature and avoid mistakes on your final product.
The most common problems are an uneven impression caused by damp wood, burnt edges caused by excessive heat or a faint impression caused by insufficient heat. A dry surface, the correct temperature and a test impression on scrap material help prevent these problems.
Always apply the brand mark before varnishing or staining the wood. You cannot brand a varnished or stained surface. Branding after oiling is sometimes possible, but we advise against it as well. Burn your logo into the wood first and apply the finish afterwards.
Usually not. In some cases, lightly sanding the wood can help remove small scorch marks around the logo if too much heat or pressure was applied. No other finishing is generally required. We are happy to advise you on the best finish for your material.
Our branding irons work on almost every type of wood. Hardwood such as oak, beech and walnut produces the sharpest and darkest result, while softwood such as spruce and pine burns more quickly. The most important thing is that the wood is dry, clean and flat, so the entire stamp makes proper contact.
A brand mark is burned into the wood itself and does not fade. It remains visible even with intensive use, moisture or sunlight. It will only disappear if the wood itself begins to rot. For outdoor use, we recommend applying a protective layer of oil or varnish. Always create the brand mark before applying varnish.
You can upload the following file types:
– .jpg
– .jpeg
– .png
– .svg
– .eps
– .psd
– .dxf
– .pdf (high quality)
– .ai (Adobe Illustrator)
– Vector files
– Word files
Please keep the following in mind when submitting your logo:
– High resolution (minimum size required)
– Clear and sharp contours
– Preferably a black-and-white logo
Your logo will be converted into a black-and-white design, which is used to create a clean and precise engraving.
For the best result, we recommend uploading your logo in black and white or high contrast.
How is my design prepared?
If we have any doubts about how your logo will translate, we will always contact you before production.
100% satisfaction guaranteed
We only proceed when we’re confident your branding iron will look great.
Not satisfied? You’re covered by our no-questions-asked money-back guarantee.
Yes, absolutely. We can adjust your logo by removing text or simplifying certain elements to ensure the best possible result.
How does this work?
Simply mention your preference in the order notes, and we’ll take care of the rest.
If we have any doubts about how your logo will translate to a branding iron, we will always contact you before production via WhatsApp, phone or email.
Yes, absolutely. You can choose exactly which elements of your logo should be included or excluded.
How does this work?
During checkout, simply describe your preferences in the order notes, and our designer will adjust your logo accordingly.
Yes, all visible elements in your uploaded design — including shapes like circles — will be included by default.
Want to exclude certain elements?
No problem. Simply indicate in the order notes which parts of your design you would like to include or remove.
We always double-check
If anything is unclear, we will contact you before production via WhatsApp, phone or email to confirm the final design.
Yes, absolutely. You can indicate exactly which part of your image you would like us to use.
How does this work?
Simply mention in the order notes which elements should be included (or excluded), and we will adjust your design accordingly.
If anything is unclear, we will always contact you before production to confirm the final design.
Yes, your logo is always precisely centered on the branding iron as standard.
If you have specific preferences for the positioning, simply mention them in the order notes. We will make sure your logo is placed exactly as requested.
No, reference lines such as grey or dotted lines will not appear on the branding iron.
How do we handle your design?
We only use the elements that are meant to be part of your logo.
To be sure everything is exactly as you want, simply indicate in the order notes which parts of the image should be included or excluded.
We don’t automatically send proofs because 99.5% of our branding irons are correct on the first attempt.
This allows us to keep the process fast and ensure quick delivery without unnecessary delays.
Can I still request a proof?
Yes, absolutely. If you’d like to receive a proof, simply mention this in the order notes.
You can also include any specific instructions for your design, such as elements you’d like to remove or adjust.
Order with confidence
We carefully review every design before production.
If we have any doubts, we will always contact you first.
Not satisfied? You’re covered by our 100% money-back guarantee, making your order completely risk-free.
Yes, absolutely. You can request a proof before production.
Simply mention in the order notes that you would like to receive a proof, and we’ll send it to you for approval before we start production.
Why don’t we send proofs by default?
We don’t automatically send proofs because 99.5% of our branding irons are correct on the first attempt. This allows us to keep the process fast and your delivery time short.
The best size depends on how you want your logo to appear on the branding iron.
How does sizing work?
Your logo is usually scaled to fill the branding iron as much as possible, while keeping the original proportions.
It’s also possible to place a smaller logo on a slightly larger plate.
For example: a 30 × 30 mm logo can be placed on a 35 × 35 mm branding iron.
Prefer a specific size or margin? Simply mention it in the order notes.
Which shape should i choose?
For the best result, we recommend matching the shape of your logo:
Mix & match is also possible
You’re not limited to matching shapes. For example, a round logo on a square branding iron is also possible, depending on your preference.
Your logo is always scaled to fill the branding iron as much as possible, while keeping the original proportions intact.
How does sizing work?
What does this mean for your design?
Your logo will appear as large, sharp and clear as possible within the size of the branding iron.
We always check all logos in advance. If we think the logo might not be clear, we will contact you. 99.5% of the branding stamps we produce are perfect on the first try.
Would you like to receive a test print? Please indicate this in the order notes. Do you have special requests for your uploaded image (for example, certain parts you want to leave out)? Please also indicate this in the notes.
100% satisfied or your money back
We offer a 100% satisfaction guarantee. We are the only company in the Netherlands that offers a 100% satisfaction guarantee on a custom-made product.
Yes, the result is the same. The main difference is that an electric branding iron is easier to heat and simpler to use, as no external heating is required. In addition, an electric branding iron can maintain a constant temperature when used with a voltage regulator, making it easier to achieve consistent results.
Yes, larger sizes are available on request.
What should you consider with larger branding irons?
For the best result, the surface you’re branding must be completely flat and evenly heated.
With larger branding irons, this can be more challenging, which may affect the clarity of the imprint.
Need advice on larger sizes?
We’re happy to help you choose the right size for your application.
Feel free to contact us via phone or email to discuss the possibilities.
Do you also sell replacement heating elements?
Yes! To order replacement heating elements for our branding irons, please contact us. The rod connecting the burner plate and the heating element must be the correct size. If it is not, the stamp may need to be modified, which could incur additional costs.
The rods suitable for our heating elements have diameters of 9.5 mm, 13 mm, and 19 mm. Contact us and we will gladly advise you on the best heating element for your needs.
Yes, this is possible. Branding plates can be easily attached and removed using a screwdriver.
What should you keep in mind?
To ensure the best performance, it’s important that your heating element is suitable for the new plate:
Feel free to contact us, we’ll gladly advise you on the right combination for your setup.
English (UK) 
Nederlands 
Deutsch 
Svenska 
